testtest

Lab4Us and the Terrible, Horrible, No Good, Very Bad Range Day

Lab4Us

Master Class
Spoiler Alert - SAVED at the end!

Today’s goal was to catch up rounds fired in my not fired yet SW 432 Ti .32 HR Magnum to my Ruger LCR .32 HR Magnum. Out of 303 various rounds total, the idea was 49 total out of the LCR and all the rest out of the SW…ahhhh, the best laid plans…and all that.

Started with this as a warm up. Circles 1 and 4 were Hornady Critical Defense FTX .32 Magnum, Circles 2 and 5 were Sellier & Bellot .32 SW Long Wadcutters, and Circles 3 and 6 were Federal Hydra Shok Deep .32 Magnum. This part went pretty well, mix of 2h standing and 1h strong side.

IMG_4781.jpeg


All the rest were meant to be from the SW 432 Ti. Managed to get 20 rounds of the Hydra-Shok and 6 rounds of the Sellier & Bellot into the below target before I couldn’t get the cylinder open. Man handling it a bit, I finally got it open, ejected spent casings and reclosed cylinder to make sure it was going to work…it did not…no matter what I did, I could not get it open. Didn’t have pliers or screw driver in bag either, so not much I could do. Fortunately I had the LCR, so while I couldn’t keep rate of rounds fired relatively even, I COULD continue to hone my skills. Although all the following targets read SW 432 Ti .32 Magnum, they are all the Ruger LCR .32 Magnum with the exception of the 26 rounds mentioned above.

IMG_4782.jpeg


After those 3 yd warm ups, some right hand, some left hand, some 2h, some .32 Mag and some .32 SW Long Wadcutters, set up a new target at 7 yds.

IMG_4783.jpeg


Same things at 7yds I did at 3yds. Then set up a final target to do my favorite drill…

5 rounds right shoulder, 5 rounds left shoulder, slow fire, 3 yds
10 rounds center fast fire, 5 yards
10 rounds center fast fire, 7 yards
5 rounds slow fire, 10 yards
5 strings of 2 to center, 1 to head, fast as possible, 3 yds

This was 50 rounds of Hornady FTX .32 Magnum.

Though I had to use the LCR instead of the SW, pretty happy with the results. A little spread out, but all hits, and THIS saved my range day! Figured not too shabby for 2” snubby…especially after 250 snubby rounds before the drill, a good number of them magnum rounds.

IMG_4785.jpeg
 
Wasn’t the shooting that made it a bad day, it was that I didn’t get enough range time with the SW 432 once the cylinder locked up.

Was able to have LGS/Range armorer get it undone for me, then show me how I can fix it next time with pliers…which are already in my bag 😆.

IMG_4780.jpeg
 
Wasn’t the shooting that made it a bad day, it was that I didn’t get enough range time with the SW 432 once the cylinder locked up.

Was able to have LGS/Range armorer get it undone for me, then show me how I can fix it next time with pliers…which are already in my bag 😆.

View attachment 79213
Why would you have to have pliers to open the cyl. ? Sounds like maybe a trip back to factory might be needed.
 
Why would you have to have pliers to open the cyl. ? Sounds like maybe a trip back to factory might be needed.
The ejector rod had worked itself loose and would not allow cylinder to open. Shrouded so I can’t get my finger(s) in there to tighten it while cylinder closed. On the front of the 432, just under the barrel, the little spring piece that moves forward when using the cylinder release sticks out enough to grab hold of with pliers and pull forward to allow cylinder to release, then can properly retighten ejector rod.

Now if the rod loosens every time I shoot a few dozen rounds through it, it will likely go back. I’m hoping it just wasn’t QC’ed properly when leaving factory and now that it’s properly tightened, the issue should not reoccur.
 
The ejector rod had worked itself loose and would not allow cylinder to open. Shrouded so I can’t get my finger(s) in there to tighten it while cylinder closed. On the front of the 432, just under the barrel, the little spring piece that moves forward when using the cylinder release sticks out enough to grab hold of with pliers and pull forward to allow cylinder to release, then can properly retighten ejector rod.

Now if the rod loosens every time I shoot a few dozen rounds through it, it will likely go back. I’m hoping it just wasn’t QC’ed properly when leaving factory and now that it’s properly tightened, the issue should not reoccur.
Whatever you do don’t put LocTite on the threads.
 
Back
Top